Estoy ayudando a un amigo a terminar una pequeña remodelación en un apartamento MIL.
Tema actual: Baño
Estoy tratando de conectar un nuevo ventilador/luz a los interruptores separados en la pared. Quiero que (1) la luz del tocador de pared se encienda con la (3) luz del techo. Y el ventilador para funcionar de forma independiente.
Cableado: Estoy tratando de no cavar en lo que está en la caja de conexiones detrás de la luz del tocador u otro extremo del cable en la caja de interruptores. (Tengo miedo)
1.a. El accesorio de iluminación de tocador tiene un ventilador/caja de luz de 14/2 (el negro es caliente de 120 V, sin V en neutral)
1.b. Hay un recorrido de 14/3 desde la caja del ventilador/luz hasta la caja del interruptor de pared (sin V y con continuidad comprobada)
1.c. La caja de pared Gang doble recibe el 14/3 del ventilador/caja de luz y un 14/2 ((¿Circuito de interruptor?) El blanco está caliente 120 V y no hay V Negro))
Traté de hacer funcionar mi fuente de alimentación 14/2 (bucle de interruptor con Hot White) con colas de cerdo en la caja de interruptores a ambos interruptores y al negro (ahora conectado al neutral 14/3). Luego ejecuto un 14/3 negro (ventilador) y rojo (luz) desde los terminales de salida de energía al dispositivo y conecto 14/3 negro al ventilador y 14/3 rojo a la luz. La luz del techo se encenderá con el interruptor (todavía es necesario conectar el tocador) El ventilador no se encenderá con su propio interruptor.
No estoy seguro de qué fuente usar o si hay una manera de vincularlas (ambas fuentes) o usar una y tapar la otra.
Notas adicionales:
Mediciones : tomadas con Fluke 87 III, usando tierra del mismo cable que se está midiendo.
en la caja de interruptores: 14/2 proviene de la luz del tocador
Interruptor abierto:
Blanco = 119,9 +/- V
Negro = 099,0 +/- mV
Interruptor cerrado: luz del tocador encendida (V medido a través de los terminales del interruptor)
Blanco = 119,5 +/- V
Negro = 119,5 +/- V
en el ventilador/caja de luz: 14/2 proviene de la luz del tocador (no está conectado a nada)
Interruptor abierto:
Blanco = 099,0 +/- mV
Negro = 119,9 +/- V
interruptor cerrado - luz del tocador encendida (no conectada a nada)
Blanco = 0,37 +/- V
Negro = 120,4 +/- V
¿Tiene problemas con la solución proporcionada, necesita una aclaración sobre los puntos de conexión y los paquetes de cables, faltan algunos cables? No sé cómo cerrar el circuito. Traté de reescribir los pasos para mayor claridad sin éxito.
Sinceramente
Turn the power off, of course
Box 2 (switch box)
b. Connect all grounds together in box 2 and to a box ground pigtail (if it's a metal box)
a. Connect the white wire from the /2 in box 2 to the white wires from the light and fan there.
- ?(no wires from fan / light, except /3 white)
c. Connect the black wire from the /2 cable in box 2 to the white wire in the /3 cable and mark that white wire as a hot.
- ?(black wire from the /2 cable is not hot)
g. Connect the white wire from the /3 cable to the HOT terminal on the fan controller after marking it as a hot.
h. Connect the black wire from the /3 cable in box 3 to the 1-POLE terminal on the fan controller.
k. Connect the red wire from the /3 cable light switch 1-pole terminal -- the Adorne parts can terminate two wires on each terminal.
Box 3 (Fan / Light box)
f. Connect all the grounds in box 3 together.
d. Connect the red wire from the /3 to the blue wire from the overhead light.
e. Connect the black wire from the /3 to the black wire from the bath fan.
i. Connect the white (0 V) wire from the /2 cable in box 3 to the switch HOT terminal, again after marking it hot.
- ? This wire runs back to vanity not box 2
j. Connect the black (120 V)wire from the /2 cable in box 3 to the switch 1-POLE terminal.
- ? This wire runs back to vanity not box 2
Turn the power off, of course
a. Connect the white wire from the /2 in box 2 to the white wires from the light and fan there.
-(no way to connect, /3 white used at step c, this wire is also 120V)
b. Connect all grounds together in box 2 and to a box ground pigtail (if it's a metal box)
c. Connect the black wire from the /2 cable in box 2 to the white wire in the /3 cable and mark that white wire as a hot.
-( this /2 black wire is not hot)
d. Connect the red wire from the /3 cable in box 2 to the blue wire from the overhead light.
e. Connect the black wire from the /3 cable in box 2 to the black wire from the bath fan.
f. Connect all the grounds in box 3 together.
g. Connect the white wire from the /3 cable in box 3 to the HOT terminal on the fan controller after marking it as a hot.
h. Connect the black wire from the /3 cable in box 3 to the 1-POLE terminal on the fan controller.
i. Connect the white wire from the /2 cable in box 3 to the switch HOT terminal, again after marking it hot.
- ? This wire runs back to vanity not box 2
j. Connect the black wire from the /2 cable in box 3 to the switch 1-POLE terminal.
- ? This wire runs back to vanity not box 2
k. Connect the red wire from the /3 cable in box 3 to the other switch 1-pole terminal -- the Adorne parts can terminate two wires on each terminal.
Button everything back up and turn the power on.
Mismo problema con la solución de doble polo.
Imagen : (no muestra la luz del tocador conectada)
Arriba - es el ventilador/caja de luz
Medio: es la caja de interruptores de pared y el interruptor desde arriba
Inferior: es la caja de interruptores de pared y el interruptor desde la parte inferior
Cualquier ayuda es muy apreciada
gracias-todd
La fuente de alimentación de todo esto entra en la caja 1 (lámpara del tocador) y alimenta el circuito del interruptor /2 a la caja 3, así como la alimentación de /2 a la caja 2. La caja 2 y la Caja 3 están conectadas por un cable /3, aparentemente destinado a ser un bucle de conmutación.
Con todo esto, pensarías que serías capaz de:
y haz que funcione. De hecho, funcionará si haces esto; sin embargo, ¡hay una trampa! Esta disposición toma la alimentación de un bucle de interruptor (de la luz del tocador) y la devuelve por dos cables diferentes (a la luz del tocador y a la luz del techo), lo que puede verse como una violación del Código (del 300.3(B)/310.10 (H)/300.20 complex), ya que crea una gran área de bucle que emite campos magnéticos perdidos en su baño (bueno para arruinar la imagen en ese viejo televisor que tiene montado en la pared allí;).
Un enfoque más conservador sería utilizar un interruptor de dos polos para romper las dos alimentaciones calientes simultáneamente mientras se envían las rutas de retorno por donde vinieron, de la siguiente manera:
Esta disposición también funciona y mantiene los dos bucles del interruptor de luz perfectamente separados. Sin embargo, Legrand no fabrica un interruptor Adorne de dos polos, y no creo que haya placas frontales disponibles para la combinación de un dispositivo Adorne lado a lado con un interruptor estándar en una caja de dos bandas. Tendría que obtener un controlador de ventilador de factor de forma estándar (es decir, no Adorne) para hacer esto.
Anguila trifásica
ed beal
Probador101
AI Breveleri
titanes
Anguila trifásica